Somehow I got so preoccupied with putting up siding, that I forgot to take pics of the process. Iâm still not sure I did it right. There seems to be two schools of thought on how to do it:
1. Put up trim on the corners, around doors and windows, and then put up shiplap or panel siding abutting to the trim.
2. Put up siding abutting doors and windows as well as overlapping itself at the corners, and then put trim on top.
Shed has been in use for quite some time, and Iâve been so excited to move in, I forgot to publish another quest in my step. So, here it is: today weâll be installing windows and the door.
Tools needed: knife, hammer, caulk gun
Materials needed: windows, door, flashing, Tyvek tape, silicone caulk
All right, today is an easy step: we are going to wrap the structure in Tyvek in preparation for installing windows, door, and ultimately putting on siding. Tyvek is a moisture control synthetic fabric that allows your house to breathe, and just like GoreTex clothing – expel the water vapors out, but not let the water in, so if any water gets through siding and from under the roof, it will be diverted away and wonât rot your OSB framing.
Tools needed: utility knife, stapler or Stinger (optional)
Materials needed: Tyvek wrap, Tyvek sealing tape, T-50 staples or cap nails (optional)
A long overdue update, but itâs finally here: itâs time to shingle the roof. There are quite a few steps in preparation to this, so thatâs why it took me so long. With that, letâs begin!
Tools needed: hammer, roofing nailer (optional), roofing nails, collated roofing nails (optional), tool belt (optional, but highly recommended), kneepads (optional, but highly recommended), utility knife, spare heavy duty or roofing blades, siding nailer (optional), miter saw.
Materials needed: trim boards, roofing felt paper or synthetic roofing felt (recommended), shingles, tack nails, finish nails, roofing nails or collated roofing nails (if using nailer), metal drip edge.
First, we need to put fascia on top of sub-fascia and run the trim under the roof on eve and rake ends. Get your trim boards, measure and cut. Use finish nails to put them in place, because we donât want ugly nail caps shining through pretty trim. Besides, finish nails allow the trim to move as it expands and contracts with weather.
Itâs been a while since my last update, so itâs time to fix it. I wanted to run electricity first, but itâs a whole other can of worms, so I decided to complete the roof first.
Sheathing the roof included more steps than just laying sheets of OSB and nailing them, and a few issues had to be fixed. Roof is the pinnacle of your building, so not surprisingly every small mistake you made along the way that was âgood enoughâ for the floor or the walls starts to manifest itself in the roof, and you have to deal with it.
So, letâs proceed.
Tools needed: circular saw, miter saw, framing nailer, hammer, ratcheting tie-downs (optional)
Materials needed: OSB, lumber, collated nails.
Another weekend – another construction update. Frame is ready, so itâs time to cover it in OSB, or in other words, sheathe the walls.
Tools required: framing nailer, circular saw, reciprocating saw, table saw (optional), plumb bob.
Materials required: OSB sheeting, collated nails.
Shed is 12×16, so thatâs 4 sheets of OSB on the long side, 3 on the short. Pick one sheet up, line it up straight and square against the corner on the long wall, and start nailing it in. If your walls are indeed straight and square, itâs a no-brainer, other than the fact that the 4×8 sheet of 15/32 OSB weighs quite a bit, and you want to put some kind of support underneath it, or you will never hold it in place level and long enough to nail it in. I used a bunch of 2×4 leftovers from building the frame. Other people drive in a few nails into the floor frame, but I tried and didnât like that approach.
All right, itâs time to face the most involved part of the project. No longer straight cuts, we are dealing with angles now!
Tools needed: framing square, framing nailer, measuring tape, miter saw, table saw, circular saw (optional)
Materials needed: OSB (oriented strand board), lumber, collated nails, Simpson hurricane ties.
My shed is 12×16, so the rafters span more than 10 feet. This means I have to build rafters with the bottom chord to straddle the walls. Now, we have a large triangle, and we need to figure out the angles, mark them on the pieces of lumber, cut precisely, so the pieces align with each other, and then nail together using gussets made out of OSB.
Been a pretty busy week, so had no time to work on a shed, but what is left in terms of wall construction is more of the same: cut your studs to size, line up base plates, nail the studs. Except now we have to create door and window openings.
The only difference is that both doors and windows get a header, that will support the load on the increased opening, and windows also get a sill. But first, we interrupt this program to bring you some more lumber:
A few extra pieces coming right up.
Tools required: miter saw or circular saw, framing nailer, measuring tape, rafter square.
Materials required: lumber, collated nails.
I know I said I would be doing rafters next, and in fact I did, but I wonât tell you about it just yet. Rafters are probably the most involved piece of construction there is (due to angles), and truly deserve their own chapter. What happened is that after I constructed a few of them, I realized the roof pitch might be too steep and too high. I donât want my shed to stick out of the yard like a Freedom Tower calling on the neighbors: âyo, motherfuckers, check dis out!â In fact, the less attraction it gets from the city inspectors, the better. After all, this is an illegally constructed shed (even if itâs up to all codes).
New saw – new construction updates!
Today we will be sheeting the constructed floor frame.
Tools required: good circular saw (or a big-ass table saw if you run a woodworking shop), framing nailer, adhesive gun, tape measure (optional).
Materials: OSB T&G (Oriented Strand Board, Tongue & Groove), construction adhesive, collated nails.
This is a pretty simple step if your frame is level and square – that is, of course, if you didnât spare any effort on your foundation. If itâs not – lord have mercy on your poor soul. We will be using 3/4â 4×8 sheets of OSB with a tongue-and-groove system. These sheets click into each other and form a tightly jointed floor.
Tongue on one end, groove on the other. What a concept!